M24C16-RMN6TP IC

Technical Specifications of M24C16-RMN6TP

Datasheet	M24C16-RMN6TP datasheet
Category	Integrated Circuits (ICs)
Family	Memory
Manufacturer	STMicroelectronics
Series	–
Packaging	Tape & Reel (TR)
Part Status	Active
Format – Memory	EEPROMs – Serial
Memory Type	EEPROM
Memory Size	16K (2K x 8)
Speed	400kHz
Interface	I2C, 2-Wire Serial
Voltage – Supply	1.8 V ~ 5.5 V
Operating Temperature	-40°C ~ 85°C (TA)
Package / Case	8-SOIC (0.154″, 3.90mm Width)
Supplier Device Package	8-SO

Introduction

The M24C16-RMN6TP is a 16-Kbit EEPROM (Electrically Erasable Programmable Memory) that is compatible with the I2C bus and can be used in a wide range of electronic devices. This memory device is flexible and easy to use because it is made up of 2K by 8 bits. The goal of this detailed guide is to look at the M24C16-RMN6TP EEPROM’s features, specs, and possible uses.

Overview of M24C16-RMN6TP

The M24C16-RMN6TP is one of the EEPROMs in the M24C16 line, which also includes the M24C16-W and the M24C16-F. The “R” in the part number means that this device can be read and written to with a source voltage between 1.8 V and 5.5 V. This means that it can be used in both low-voltage and standard-voltage systems.

Features

The M24C16-RMN6TP is a 16-Kbit EEPROM, which means it can hold 16,384 bits of data in total. It is set up as 2K x 8 bits, where “8 bits” denotes the data width at each address and “2K” denotes the total amount of memory addresses (2,048 addresses). Byte-sized data pieces can be efficiently stored and retrieved because of this structure.

● (1.8 V to 5.5 V) Wide Voltage Range

Its broad operating voltage range is one of the most notable characteristics of the M24C16-RMN6TP. At supply voltages as low as 1.8 V and as high as 5.5 V, it can operate. It is appropriate for integration into a wide range of electronic systems, including those with minimal power requirements and those running at normal voltages, thanks to its wide voltage tolerance.

● I2C-Compatible Interface

The M24C16-RMN6TP interfaces with microcontrollers and other peripheral devices via the I2C (Inter-Integrated Circuit) communication protocol. The I2C interface has a number of benefits, including multi-device communication, simplicity, and ease of use. This compatibility guarantees a smooth connection between the controlling device and the EEPROM, permitting effective data management.

● (400 kHz or less) Operating Clock Frequency

The EEPROM runs at a clock frequency of 400 kHz or less. The speed at which data can be read from or written to the EEPROM depends on the clock frequency. Since data can be sent reasonably quickly at the 400 kHz frequency, the EEPROM can meet the demands of a variety of applications. Additionally, the choice of lower frequencies permits the integration into systems with more precise timing requirements or longer data transmission distances.

The M24C16-RMN6TP EEPROM features a large voltage range of 1.8 V to 5.5 V with a 16-Kbit storage capacity, structured as 2K x 8 bits. Its I2C-compatible interface makes communicating with microcontrollers simple, and its 400 kHz (or lower) clock frequency provides effective data transfer and manipulation. The M24C16-RMN6TP is a great option for a wide range of electronic applications that need for dependable and adaptable data storage capabilities thanks to these essential qualities.

Operating Conditions of M24C16-RMN6TP

● Temperature Range for Reliable Operation

The M24C16-RMN6TP EEPROM is ideal for usage in a variety of environmental settings because it is designed to function dependably over a broad temperature range. Typical EEPROMs like the M24C16-RMN6TP can frequently withstand temperatures from -40°C to 85°C or even wider. The precise temperature range specified in the datasheet may vary depending on the manufacturer.

Any electronic component’s operating temperature range must be taken into account since excessive temperatures can have a negative impact on the component’s performance and durability. Temperatures can change drastically in severe industrial settings or in automobile applications. The M24C16-RMN6TP can survive situations that would be harmful to other components not made for such extreme conditions because it can operate in a wide variety of temperatures.

Moreover, it is essential to confirm that the EEPROM meets the necessary performance requirements at both low and high temperature extremes when utilizing it in situations where temperature can vary greatly. To guarantee constant and dependable functioning in challenging settings, proper heat management and insulation could also be required.

● Importance of Adhering to Specified Voltage Ranges and Avoiding Voltage Spikes

For the M24C16-RMN6TP EEPROM to operate correctly and last a long time, adherence to the recommended voltage ranges is crucial. Operating the device below the minimum voltage may lead to inconsistent read and write operations, corrupted data, or possibly irreparable EEPROM damage. However, going beyond the maximum voltage limit could result in catastrophic failure and irreparable harm.

Voltage spikes are sudden, transient increases in voltage that can happen for a variety of reasons, including changes in the power supply or electromagnetic interference. The EEPROM and other delicate electrical components may suffer harm as a result of these voltage spikes. Despite being capable of handling a wide range of voltages, the M24C16-RMN6TP must nevertheless be shielded from unexpected voltage spikes.

The right voltage management and protection techniques must be used by designers and engineers to guarantee the EEPROM’s optimum performance and longevity. In order to reduce voltage spikes and stabilize the supply voltage, this can involve the use of voltage regulators, capacitors, and transient voltage suppressors (TVS). The risk of noise coupling and interference can also be reduced by using careful circuit design and layout techniques.

Applications of M24C16-RMN6TP

Given its adaptability and dependable performance, the M24C16-RMN6TP EEPROM is an excellent choice for a variety of electronic applications, including the following:

Embedded Systems

● Calibration Data Storage

Accurate calibration data is frequently needed for sensors, actuators, and other parts in embedded systems. This vital calibration data can be stored by the M24C16-RMN6TP, assuring precise and ideal system functioning.

Configuration Settings

Embedded systems frequently contain programmable parameters that determine how they behave. These configuration settings can be stored in the EEPROM, enabling the device to maintain its preferences even after power cycles.

Consumer Electronics

● Storing User Preferences

The M24C16-RMN6TP enables devices like smart TVs, audio systems, and IoT devices to save user preferences like display settings, audio settings, network setups, and customized profiles.

Device Settings

Device-specific options for consumer electronics include language preferences, power modes, and customized user settings.

Automotive Electronics

● Infotainment Systems

In order to provide a customized in-car experience, the M24C16-RMN6TP can be linked into vehicle infotainment systems to record music preferences, navigation preferences, and entertainment selections.

Advanced Driver-Assistance Systems (ADAS)

ADAS applications require the storage of calibration data for cameras, sensors, and radar systems. The EEPROM can securely store this data to maintain the accuracy and reliability of ADAS functionalities.

Dashboard Displays

Automotive dashboard displays often store user preferences for instrument cluster settings, warning thresholds, and other vital information.

Industrial Automation

● Process Data Storage

Systems for industrial automation produce an enormous amount of process data. This information, which can be stored in the M24C16-RMN6TP and used for system analysis and troubleshooting, includes production parameters, sensor readings, and operational logs.

● Configuration Parameters

Configuration parameters for industrial automation equipment are frequently needed, including communication settings, PID values, and control setpoints. These settings can be maintained by the EEPROM, assuring consistency and continuity in operation.

Conclusion

In conclusion, the M24C16-RMN6TP stands out as a feature-rich and reliable 16-Kbit I2C-compatible EEPROM, offering versatile data storage capabilities that cater to a wide range of electronic applications. With its impressive operating voltage range, low power consumption, and I2C interface, it proves to be an excellent choice for modern electronic designs.

To take advantage of the M24C16-RMN6TP’s remarkable features and unlock its potential for your electronic designs, we encourage you to order now from ICRFQ, the leading distributor of electronic components in China. Our reliable services and commitment to quality will ensure a smooth and successful integration of this EEPROM into your projects. Don’t miss out on this opportunity; secure your order today and revolutionize your electronic designs with the M24C16-RMN6TP!

The Latest And Most Popular Parts That You May Also Like